ASTM D4000 PDF

Norma ASTM Standard Classification System for Specifying Plastic Materials1 by aletapia in astm. Find the most up-to-date version of ASTM D at Engineering ASTM D − Standard Classification System for Specifying Plastic Materials. R&B Inc. 편집자 주. ▫ 본 한글 본은 R&B Inc. 내부재료로 일부 용어는 표준용어.

Author: Faurisar Malajar
Country: Djibouti
Language: English (Spanish)
Genre: Travel
Published (Last): 22 July 2004
Pages: 404
PDF File Size: 10.27 Mb
ePub File Size: 15.66 Mb
ISBN: 454-3-64839-279-7
Downloads: 17989
Price: Free* [*Free Regsitration Required]
Uploader: Zulkijas

Add to Alert PDF. Add to Alert PDF.

ASTM International – Standard References for ASTM D – 16

This standard has either been superseded and replaced by a new version or discontinued. When the requirements for a material are included in this standard, the following sections are applicable.

Note 1—The classification system serves many of the needs of industries using plastic materials. The standard is subject to revision as the need requires; therefore, the latest revision should always be used. This section may also include descriptions of the changes or reasons for the changes, or both.

Link to Active This link will always route to the current Active version of the standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. If necessary, additional control of these reinforcements shall be accomplished by the use of the suffix part of the system Section 7.

These tables should be used in the same manner as the cell tables that appear in the material speci? Please first log in with a verified email before subscribing to alerts. The generic family is atsm Added ISO and -2 as references for second letter M. A system is thus established which, together with values describing additional requirements, permits as complete a description as desired of the selected material.

When using this classification system aastm two-letter, three-digit suffix system applies. Note 3—When a material is used to fabricate a part where the requirements are too specific for a broad material callout, it is advisable for the user to consult the supplier to secure callout of the r4000 to suit the actual conditions to which the part is to be subjected.

  LIBRO SOCIEDAD ELY CHINOY PDF

Proceed to Checkout Continue Shopping. If the document is revised or amended, you will be notified by email. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM D4000 – 16

The standard is subject to revision as the need requires; therefore, the latest revision should always be used. Please first verify your email before subscribing to alerts. Cell Limits 4 55 2 Standards Subsctiption may be the perfect solution.

It indicates change in hardness, tensile strength, elongation, and volume. If the document is revised or amended, you will be notified by email. Subscription pricing is determined by: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The reinforcement letter designations and associated tolerance levels are shown in Table 2.

Cell Limits 4 85 10 When the existing cell table does not adequately describe the material, then suffixes may be used in place of a cell table designation. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Historical Version s – view previous versions of standard. The report shall consist of results of the lotacceptance inspection for the shipment and the results of the most recent periodic-check inspection.

This standard is also available to be included in Standards Subscriptions. Additional symbols will be added to this table as required. Replaced by Test Methods D and D Cell Tables A and B have been reserved for the referenced standards and will apply to un? We have no amendments or corrections for this standard. This standard is not included in any packages.

  CLOPPER THE CHRISTMAS DONKEY PDF

Note 2—When using this classification system the two-letter, three-digit suffix system applies. Proceed to Checkout Continue Shopping. Subscription pricing is determined by: D — 00a: Suffix Requirements G Speci? The cell tables that may be used for each generic family are listed in Table 1. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. Please first verify your email before subscribing to alerts.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Material selection should be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the inherent properties of the material not covered in this document, and the economic factors. When using this classification system the two-letter, three-digit suffix system applies.

NOTE 6—An example using the group, class, and grade is as follows: A system is thus established which, together with values describing additional requirements, permits as complete a description as desired of the selected material.

By its designation, certain inherent properties are speci? It further provides a means for specifying these materials by the use of a simple line call-out designation. Likewise, when an acceptable value is not available in the cell table, the number 9 should be used and a suffix used indicating the speci? These characteristics will be spelled out in detail and identi?